![]() The benefit of the C setting is longer battery life. A=Most Sensitive, B=Normal, C=Least Sensitive. Using a different gauge of wiring could disturb the proper operation of your unit.Ī: Emitter: Vibration Sensitivity Jumper Switch is located under one battery in the Emitter (Red LED). A replacement board is found on this webpage: Wayne Dalton Quantum Control BoardĪ: 22 gauge wiring is used for our units. If you are unsuccessful in programing the transmitter to the motor head unit or if the button does not operate the door you probably have a faulty motor control board. Press the same button on the Transmitter once more to operate the door. The PROGRAM STATUS light will turn off indicating a successful learn. The PROGRAM STATUS light on the motor head unit will turn on and remain lit for one minute, indicating that it is ready to learn the Transmitter code. Press the PROGRAM button located on the garage door motor head unit once. Programming Transmitter to Power Head Unit If that doesn't work try to reprogram your remote control to the power head using the steps below: ![]() This helps conserve battery life because the sensors only turn on when the door is activated and moving.Ī: First try resetting your opener by unplugging the opener power head from the wall outlet. These sensors are activated by door vibration. ![]() Keypad InstructionsĪ: You must attach your garage door in order for the Wireless Sensors to function properly. To find the radio frequency look on the sticker on the back of a remote control that operates the opener or on the sticker on the back of your garage door opener powerhead.Ī: Below is the webpage with instructions for your keypad. To find the model number look on the sticker on the back of your garage door opener powerhead in the garage. You may also refer to the manuals section of this Web site.Ī: Repeat the process you used to program the first remote on the second one.Ī: You may program up to four (4) garage door openers per Keyless Entry Pad.Ī: You may only program one (1) keyless entry pad per unit.Ī: To select the correct remote controls, keypads, wall stations, and control boards for your Wayne Dalton Quantum garage door opener you will need to know the model/series number of your garage door opener (Quantum 3212, etc) or the radio frequency for your opener (303Mhz or 372Mhz). Program switch needs to be pressed and held (if status LED is not on) until status LED does flash or pressed and released (if status LED is already flashing). HomeLink Conversion KitĪ: Programming: Set Emitter to align (Green Transponder LED should blink). 2) Be sure the green LED is solid before flashing during Step 2 of Changing Transmitter Code.Ī: We have a Homelink Conversion Kit 1 that will make your openers compatible with your vehicles. TIPS: 1) Unplug other garage door openers or any signal transmitting devices in the garage. Replace batteries in both Photoelectric Sensors and in the Wall Station.Ī: If your transmitter has a green LED, be sure to follow the Changing Transmitter Code (refer to Programming Transmitters section of this Web site). The only replacement remote control for your opener is the Wayne Dalton 3-Button Full Size Remote Control.Ī: The cause is weak batteries in your Wireless accessories. Only Wayne-Dalton transmitters will work with a Wayne-Dalton opener.Ī: The one button version is no longer manufactured. Q: Wireless Wall Station will not program.Ī: No. Q: What remotes are compatible with the Quantum 3312, and 3313? Q: What is the purpose of the A,B,C settings in the Wireless Photoelectric Sensors? Q: What is the gauge of wire used for the wired Photoelectric Sensors and Pushbuttons? Q: My garage door opener will work using the button on the wall in the garage, but the remote for the car will not work. The Trolley travels a short distance from the Open position and reverses. Q: I've programmed my Wireless Photoelectric Sensors. Q: I have lost the instructions for my keypad. Q: How to Select the Correct Remote Control or Keypad Q: How many Keyless Entry pads can I program to my unit? ![]() Q: How many garage door openers can I program with one Keyless Entry Pad? Q: How do I program two transmitters to the same opener? Q: How do I program my Wireless Photoelectric Sensors? Q: How do I make my Wayne Dalton Quantum model 3212, 3213 Opener work with my built-in car remote control? Q: Hand-held remote (Transmitter) will not program. Q: Door hesitates during downward travel when activating my Wireless unit Q: Do you have a one button transmitter for a wayne dalton Quantum 3212? Q: Can I use my Transmitter (remote) from another opener with the Wayne-Dalton opener? ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |